Meniu Închide

Technology of Placing gypsum tiles with your hands

Gypsum tiles have to be laid properly, as not only the aesthetic look of cosmetic facing, but in addition the service quality of

the material will be based on the technology of job. The product is universal, and it can be attached to plaster, concrete, brick

or gypsum board sheets, provided the top layer of the base is even and has no flaws.

If the flaws of this foundation are important, it ought to be thoroughly treated with primer, then a cement mortar is created,

which matches all of the cracks. Subsequently the surface ought to be primed and dried. In cases like this, its composition should

pick a particular, comprising elements which block the look of fungus and mold.

In today’s interior of the rooms most frequently used gypsum tiles, imitating natural stone or brick. To execute cosmetic

finishing yourself, it is necessary first of all to select a strategy of tile placement and prepare a solution. It’s important to

pay attention to the reverse side of the substance. If its surface includes an embossed surface, then the glue should be placed

with an even trowel, and if it’s even, then using a top notch one.

The tech of the job is as follows:

* A thin coating of glue is applied to the pre-prepared wall. It’s spread over the foundation so that it is likely to place 4-5

tiles. Decorative cladding can be put both on plasterboard, and on putty.

* Glue the back side of the tiles with adhesive.

* Plaster elements are pressed against the walls and their place is adjusted. To align with the seams, it’s suggested to use


* Finishing is performed in rows, each of which should be changed by half a tile. Facing is completed to the corners of the

room, then immediately eliminate any remaining mortar in the joints.

Drying the walls requires no more than a day and needs a constant humidity and temperature within the room. The last point in the

placing of gypsum tiles is that their decor. To try it, the joints between the components are full of a special solution, the

shade of which matches the brick.

Decorative imitation of brickwork around the walls will be carried out in the following ways:

* Cutting on the surface of the seams of masonry using a bolt cutter with your own hands;

* laying of tiles beneath the brick:

* mimicking the format and colour of the side of a single brick;

* Imitating a fragment of brickwork of many bricks.

The best way to decorate”under the brick” would be the one that allows you to create a practical coating with the maximum

appearance of its similarity to organic masonry. All 3 strategies to execute this kind of finishing works meet the requirements,

but the cutting edge of joints with a bolt is labor-intensive and also the creation of large amounts of dust, and so let us

consider more prevalent manners.

The old finish is removed from the walls, and also the surface, if necessary, is leveled to get rid of the requirement to glue

plaster onto a thick layer of adhesive.

Combining these cladding with different types of interior finishes could be both orderly and performed with no apparent

consistency, chaotically, with fake of signs of aging.

With the help of decorative gypsum tiles it’s possible to mimic a lot of textures.

A large number of textures could be imitated with the support of cosmetic gypsum tiles.

The wall where it’s to be installed must possess the following characteristics:

* Hardness and durability of the outside;

* The lack of irregular areas and sharp differences;

* not any deformations.

Cosmetic tiles in the interior of the kitchen

Walls are created from a number of substances, so let us break down the individual rules of installment.

When dealing with concrete, there’ll be no big problems. It is just necessary to take into account the porosity of the material.

Concrete, which has virtually no pronounced pores, ought to be treated with a fantastic primer.

Mounting gypsum tiles on concrete

Before beginning work on the installation of gypsum tiles in the walls, it is worth checking the strength of their surface. When

the plaster doesn’t drop off the wall and in precisely the identical time holds nicely, you can simply paint it using primer.

Mount the tiles on the painted concrete should not. The surface should be scratched, making sure to misfire, then it ought to be

grouted and coated with a layer of plaster.